Command Summary
17
5.3
Communication
When communication of either text or commands is interrupted, try the steps below.
?
First, check the communication cable for continuity. If you don't have an ohm meter, try using a
different communication cable. If you are using a PC try using a different Com/USB Port.
?
Next, please ensure that the display module is set to communicate on the protocol that you are
using, by checking the Protocol Select Jumpers.
?
In serial and USB protocols, ensure that the host system and display module are both
communicating on the same baud rate. The default rate for the display module is 19200 bps.
?
Match Rx from your display to the transmitting pin from your host and the Tx pin to the
receiving pin.
?
If you are communicating to the display via I2C*
please ensure that the data is being sent to the
correct address. The default slave address for the display module is 80.
?
In I2C mode, connect Rx to the clock line of your controller and
Tx to the data output.
?
Unlock the display. See the Set and Save Data Lock command for more info.
?
Finally, you may reset the display to its default settings using the Manual Override procedure
outlined below.
*Note:
I2C communication will always require pull up resistors on SCL and SDA of one to ten kilohms.
5.4
Manual Override
Should the settings of your display become altered in a way that dramatically impacts usability, the
default settings can be temporarily restored. To override the display, please follow the steps below.
1.
Disconnect power from your display.
2.
Place a jumper on the two manual override pins, for the GLK240128-25
model these are the middle
two keypad pins, for the GLT240128
these are the two pins near the keypad header.
3.
Reconnect power to your unit, and wait for the start screen before removing the jumper. Please
note the jumper will adversely affect GLT240128performance if left in place during use.
4.
Settings will be temporarily**
overridden to the defaults listed in the Manual Override Settings
table. At this point any important settings, such as contrast, backlight, or baud rate, should not only
be set but saved so they remain when the override is removed.
Parameter
Value
Backlight
255
Contrast
128
Baud Rate
19200
I2C Address
80
Table 15: Manual Override Settings
**Note:
The display module will revert back to the old settings once turned off,
unless desired settings are saved.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
GM2BB50BM0C
LED WHITE 5000K 150MA 0.5W
GM5YJ01210A
LED ORANGE CLEAR 6050 SMD
GU128X128D-3900B
VACUUM FLUORESCENT DISPLAY
GU144X16D-7053B
VACUUM FLUORESCENT DISPLAY
GU160X32-800B
MODULE VF GRAPHIC DISPLAY 160X32
GU160X80E-7900B
VACUUM FLUORESCENT DISPLAY
GU256X128C-3900
MODULE VF GRAPHIC DISPLY 256X128
GU256X128D-3900B
MODULE VF GRAPHIC DISPLY 256X128
相关代理商/技术参数
GLT240128-GW
功能描述:LCD 图形显示模块和配件 240x128 w/ Touch Blue w/Black Text RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk
GLT240128-USB
功能描述:LCD 图形显示模块和配件 Graphic Touch Disp USB, Yellow/Green RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk
GLT240128-USB-FGW
功能描述:LCD 图形显示模块和配件 Graphic Touch Disp USB, White/Grey RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk
GLT240128-USB-WB
功能描述:LCD 图形显示模块和配件 Graphic Touch Disp USB, Blue/White RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk
GLT240128-VPT
功能描述:LCD 图形显示模块和配件 240x128 Blk Text T/S Y/G B/G Volt Reg
RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk
GLT240128-WB
功能描述:LCD 图形显示模块和配件 240x128 w/ Touch Blue w/White Text RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk
GLT240128-WB-V
功能描述:LCD 图形显示模块和配件 Blue Background White Txt Wide Volts RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk
GLT240128-WB-VPT
功能描述:LCD 图形显示模块和配件 240x128 Wht Txt Blu B/G Volt Reg
RoHS:否 制造商:ELECTRONIC ASSEMBLY 产品: 分辨率:128 x 64 流体类型:FSTN Positive 接口: 背光: 背景色:White 工作温度范围:- 20 C to + 70 C 封装:Bulk